1 AVer IP Camera User Manual
10 Name Function To Add Filter 1. Click Add Filter in User Management > Connection tab. 2. In Rule drop down list, select from the 3 types of
11 *(2)(3)(4)(1) Name Function (1) Device Name Assign name for the IP camera. (2) Network HW Switch Enable/disable to use the IP camera dip swit
12 Name Function (4) IPv6 Settings Enable IPv6 support Select “Manually set the IP address” to specify IP address manually. System > Network &
13 To use this feature, you need to register a domain name at http://dyn.com/dns/ . Enter the DDNS domain name, user, password and enable DDNS enable
14 System > Network > Others In Others tab, you can configure the enable/disable the UPnP setting. If your router does not support UPnP functio
15 System > Image Both admin and operator levels can adjust the Image setting. There are 5 tabs: OSD, Preference, Exposure, Advanced, and Privacy
16 System > Image > Exposure In Exposure tab, you can set the exposure zone, exposure mode, and calibrate the DC Iris. After completing the set
17 Name Function (1) Exposure Area Select the exposure area choices to define the light distribution and bring out more details. Entire screen - me
18 Name Function (1) Wide Dynamic Range WDR effectively balances the video image on the screen in both bright and dark areas making it possible to
19 System > Image > Privacy Mask In Privacy Mask tab, you can enable 3 privacy masks. Simply adjust the size and position the mask on the area
2 Table of Contents Using the IP Camera Browser Interface ... 3 Live View ...
20 *(1)(2)(3)(4)(5)(6)(7) Name Function (1) Sensor Mode Select sensor input resolution from either Normal or Wide Angle. * ( Available for 3M pixel
21 Name Function VBR (Variable Bit Rate) by default use this setting if there is a need to maintain the image quality whenever there is lot of activi
22 System > Audio Both admin and operator levels can configure the IP camera audio setting. After configuring the Audio setting, click Save to app
23 (5)(2)(1)(3)(4) Name Function (1) SD/microSD Card Info Shows the SD/microSD card details. No details will appear if SD/microSD Card is not inse
24 Application > Motion Detection Both admin and operator levels can specify up to 3 areas on the screen to monitor the motion. In the motion det
25 To Set the Motion Detection 1. Click Application > Motion Detection. 2. Enable the region check box to create a motion detection frame. 3.
26 3 to add more preset locations. 4. Select the preset target area in the list and press to create the patrol sequence. The selected present tar
27 To Setup the Event 1. Click Event. 2. On the time table, click-drag to select from what time to what time to specify the period of the event.
28 - Alarm Interval This triggers the IP camera based on the set time. - Motion Detection Region 1/2/3 This triggers the IP camera when a motion i
29 Status Information Show the information about the device and network setting.
3 Using the IP Camera Browser Interface The admin have the full access to the IP camera browser interface. The menu on the left, you can expand and
4 Name Function (5) Direction buttons - Use to move the position of the view point while in zoom mode. - Use to control the position of the RS-485
5 (2)(3)(4)(5)(6)(1) Name Function (1) Reboot Restart the IP camera. (2) Reset Set all the configuration settings back to default except the user
6 Name Function System > General > Date & Time In the Date & Time tab, admin can manually set the date and time setting or synchronize
7 Name Function Manual – manually set the date and time. Click Now to set the date base on the computer time setting and Done to close the date and
8 User Type Access rights Admin Can access all the configuration pages Operator Can preview live image, modify and adjust certain settings except in
9 System > User Management > Connection In Connection tab, admin can set the total number of user to access the IP camera, and filter the IP a
Commentaires sur ces manuels