AVer EH6108H Manuel d'utilisateur

EH6000H series EH6108H+/EH6216H+ User’s Manual V. 1.10.0

2 1.1.2 EH6216H+ (1) (2) (3) (4) (5) (6) (7) (8) (9) (2) DVR unit - EH6216+ with HDMI interface - EH6216H+ w/o HDMI interface i EH62

92 3.9 Alarm Setting In the Alarm Setting dialog box, click Add to insert and set new alarm setting, click Delete to remove the selected alarm setti

93 CHAPTER 3 - Video Loss: click the camera number (01 to 16) to set the alarm condition when video is lost. Click the Detail button to setup the s

94  Network is switched off: when the network connection of DVR system is lost, the system will send out the alarm message.  Hard Disk failed: w

95 CHAPTER 3 - Enlarge Camera View Switch to only display video in Preview mode from where the alarm is activated. a. Select the camera from drop d

96 - Send E-mail Send an electronic text message. Beside the Send Email check box, click Detail. In the E-mail Setting dialog box, click OK to ex

97 CHAPTER 3 - Start Recording Record the video from the selected camera. 1. Beside the Start Recording check box, click Detail. 2. In the Alar

98 - PTZ preset point Position the PTZ camera based on the preset point setting. Beside the PTZ preset point check box, click Detail. In the Trigger

99 CHAPTER 3 3.10 User Setup Only administrator level authority can access User Setting. The maximum user accounts are 32. In the User Setting dial

100 (1) Authorization level Select the status of the user. Administrator has full authority of control rights. (2) Control Right Enable the items th

101 CHAPTER 4 Chapter 4 Using the Remote Programs User can use Microsoft Internet Explorer to access DVR system by entering the IP addres

3 CHAPTER 1 1.2 Front Panel 1.2.1 EH6108H+/EH6216H+ Name Function (1) System indicator - Power indicator (left): System power status indicator

102 4.1 Familiarizing the Buttons in PCViewer 4.1.1 PCViewer Screen Right-clicking on the PCViewer video screen, enables you to start video r

103 CHAPTER 4 i To view POS data on PCViewer, please switch to 1-split screen mode and right-click on screen to make sure the video quality is High.

104 4.1.2 PCViewer Control Panel Name Function (1) Preview Mode Switch to preview mode control panel (2) Playback Mode Switch to playback mod

105 CHAPTER 4 Name Function (6) Audio Enable/disable remote sound. (7) Remote setup Change the DVR server settings (see also Chapter 4.1.4) (8) R

106 4.1.3 Playback Mode Control Panel i The PCViewX.cab. installation is required for first time using PCViewr playback function. The PCViewX.cab in

107 CHAPTER 4 Name Function (3) Channel After select the date, please select the channel that user wants to playback or select all channels. (4)

108 4.1.4 To Setup Remote System Setting The setting here applies to Remote DVR only. 4.1.4.1 System Setting In the System Setting windows, click U

109 CHAPTER 4 - Date Format Select the date format which wants to display in Select date and time playback mode - Auto Scan Period Set the time ga

110 4.1.4.2 Camera Setting Select the camera from remote DVR servers to modify settings. In the Camera Setting windows, click Update to save and app

111 CHAPTER 4 (5) IP Camera Information To setup IP camera and display current IP camera information. IP Setting: Click IP setting to add the IP ca

4 Name Function (11) Number buttons ~ - Channel camera selection number in playback and preview mode. For the channel over 10, press , then pre

112 Analog Camera Setting Select the camera from remote DVR servers to modify settings. In the Camera Setting windows, click Update to save and apply

113 CHAPTER 4 (5) Video Adjustment Adjust the Brightness, Contrast, Hue and Saturation of the camera. Remote DVR Camera Setting Select the camera to

114 (4) Remote Camera Setting - Description Add a short comment - IP Enter the IP address of the camera - Port The port for connection - User ID

115 CHAPTER 4 (2) Recording Mode The horizontal blocks from 00 to 23 represent the time in 24-hour clock and the vertical block represent the day in

116 Record Setting of Analog Camera i EH6108H+ only supports 8 channels. (1) Camera Icons Select the camera number you want to set the recording set

117 CHAPTER 4 - Motion Recording Start recording the video from the selected camera only when the system detects movement. Once a motion is det

118 4.1.4.4 Network Setting In the Network Setting dialog box, click Update to accept the new settings, click Exit to exit without saving, and click

119 CHAPTER 4 (4) Other Configuration - Enable White List i Without any IP address/IP range is assigned in White List table, none of IP address/IP r

120 4.1.4.5 Alarm Setting In the Alarm Setting dialog box, click Add to insert and set new alarm setting, click Delete to remove the selected alarm

121 CHAPTER 4  Video Loss: Click the camera number to set the alarm condition when video is lost. Click the Detail to setup the system to send out

5 CHAPTER 1 Name Function (12) A functional key for multiple system control. Press to switch to FN mode (The word “FN” will show up in the lef

122 - Enlarge Camera View Switch to only display video in Preview mode from where the alarm is activated. a. Select the camera from drop down list

123 CHAPTER 4 - Start Recording Record the video from the selected camera. Beside the Start Recording check box, click Detail. 1. In the Alarm Re

124 - Send to CMS (Central Management System) Enable/disable the selected camera to send video to CMS when the alarm is activated. Beside the Send t

125 CHAPTER 4 4.1.4.6 User Setting Only administrator level authority can access User Setting. In the User Setting dialog box, click Add to insert

126 (2) Control Right Enable the items that would allow the user to access. (3) PCViewer Enable/disable PCViewer control right that allow the user to

127 CHAPTER 4 4.2 Familiarizing the Buttons in Remote Console Name Function (1) DirectDraw Enhance the video quality. i Direct Draw function su

128 Name Function (14) Event Log Display the Event logs, Operation logs, System logs, and Network logs. (15) Auto Scan Start/Stop video screen cycl

129 CHAPTER 4 4.2.1 To Setup Remote Console Setting Click Setup button to call out the System Setting windows. Click OK to exit and save the setting

130 (4) Channel Settings The numbers from 1 to 16 represent the camera ID. In Transmitting Channels section, enable the camera number to receive the

131 CHAPTER 4 4.3 Using the Remote Playback To use this feature, first you need to select the source of the file. In the Select Playback Mode dialog

6 Name Function (21) Zoom + / Zoom - To zoom in view of PTZ camera lens To zoom out view of PTZ camera lens 1.2.1.1 To Cut and Save the Portion

132 3. Click OK to proceed and Cancel to void this operation. 4. If you select Download Playback and after making the selection, the system divi

133 CHAPTER 4 4.3.1 Familiarizing the Buttons in Local Playback Name Function (1) Exit To close the application (2) Split Screen Mode Select fro

134 Name Function (6) Archive Select the date on the calendar and the time from 00 to 23 to where to start playing the recorded video file. i The n

135 CHAPTER 4 4.3.1.1 To Cut and Save the Wanted Portion of the Recorded Video 1. Use the Playback Control buttons or drag the bar on the playbac

136 4.3.1.2 To Search Using the Visual Search 1. Click Visual Search. 2. In the Visual Search Setting dialog box, select the Camera number and t

137 CHAPTER 4 4.3.2 Familiarizing the Buttons in RealTime Playback Name Function (1) Exit To close the application (2) Split Screen Mode Select f

138 Name Function (8) Playback Switch to Playback mode. This allows you to view the recorded video file. (9) Status bar Display the recorded date,

139 CHAPTER 4 4.3.3 Familiarizing the Buttons in Download and Playback Name Function (1) Exit To close the application. (2) Progress bar Show t

140 Name Function (10) Visual Search Search from a specific camera by Date, Hour, Minute, 10 Seconds and Second. (See also Chapter 4.3.1.2). (11) A

141 CHAPTER 5 Chapter 5 Using the Web Tools The bundled Web Tools includes Dispatch Server, Remote Backup, and Remote Setup program. To install Web

7 CHAPTER 1 1.3 Back Panel 1.3.1 EH6108H+ (HDMI supported) Name Function (1) LAN 1/LAN 2 port For Gigabit Ethernet connection (2) Audio IN/SPOT/

142 3. Click OK to complete adding remote DVR server. 4. The added DVR server will be listed and auto connects to DVR server. 5. Once the connect

143 CHAPTER 5 5.2 Remote Backup Remote Backup is purely for backing up the *.dvr file from the DVR sever. You can select between Auto Backup and Ma

144 5. Select the Backup mode: Auto Backup mode: the backup will automatically execute when the setup is completed - In Begin Date drop down calen

145 CHAPTER 5 8. For manually backup, click file select button and select the DVR to backup.

146 Appendix A Registering Domain Name DDNS (Dynamic Domain Name Service) is a data query service mainly used on the Internet for translating doma

147 APPENDIX I. Register the Domain Name on http://dyn.com/dns/ 1. Open the browser on your PC and enter the URL http://dyn.com/dns/. 2. Please re

148 Appendix B Network Service Port The following table shows the ports that DVR server uses for certain network service. Port# Variable Remot

149 WARRANTY NOTICE LIMITED WARRANTY AVer Information Inc. warrants this product to be free of defects resulting from faulty manufacture or component

8 1.3.2 EH6108H+ (None HDMI) Name Function (14) LAN 1/LAN 2 port For Gigabit Ethernet connection (15) RS232 port For POS device connection (16)

9 CHAPTER 1 1.3.3 EH6216H+ (HDMI supported) Name Function (1) LAN 1/LAN 2 port For Gigabit Ethernet connection (2) Audio IN/SPOT/TV Monitor - Au

10 1.3.4 EH6216H+ (None HDMI) Name Function (14) LAN 1/LAN 2 port For Gigabit Ethernet connection (15) RS232 port For POS device connection (16)

11 CHAPTER 1 1.4 Setting Up the DVR Unit 1.4.1 Installing the Hard Disks i The external USB hard disk only supports on file backup. Please do not u

FCC NOTICE (Class B) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may n

12 5. Turn the plate and hard disk over carefully and screw the hard disk on the plate. If hard disk cannot match to the screw hole, then, you may

13 CHAPTER 1 9. Screw the holder on the DVR unit. 10. Push the cover forward and secure the cover. 11. You may now connect all the cables and

14 1.4.2 Connecting Devices 1.4.2.1 EH6108H+ The back panel of the DVR unit, user can connect up to 8 cameras in both analog and IP camera. The DVR

15 CHAPTER 1 For backup recorded video, plugging the pen drive or external hard disk through USB port that are located at front panel of DVR unit, an

16 1.4.2.2 EH6216H+ The back panel of the DVR unit, user can connect up to 16 cameras in both analog and IP camera. The DVR unit also can connect 16

17 CHAPTER 1 For backup recorded video, plugging the pen drive or external hard disk through USB port that are located at front panel of DVR unit, an

18 1.4.3 Sensor, Relay and RS485 pinhole allocation The Sensor and Alarm enable you to connect 16 sensor inputs, 4 relay outputs and PTZ

19 CHAPTER 1 1.4.3.3 RS485 Pin Definition When connect PTZ camera through RS485 interface, please refer to the following pin definition to connect t

20 1.5 Familiarizing the Remote Controller Buttons Use the Remote controller to operate the DVR unit. Name Function (1) Switch to playback mode (

21 CHAPTER 1 Name Function (13) + : Switch to one single and 7 + 1 spilt screen display mode + : Switch to one single and 12 + 1 spilt

WARNING TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION IF THERE IS ANY DAMAGE

22 Name Function (19) ~ - As a number key for entering password in playback and preview mode - Channel camera selection number in playback an

23 CHAPTER 1 1.6 Upgrading the DVR System Firmware Please make sure your DVR model before download DVR firmware. Wrong DVR model’s firm

24 3. Then, create a folder named Update and copy the IP camera patch file that user can download from web site http://surveillance.aver.com/ same a

25 CHAPTER 1 7. After firmware upgrade is completed, the DVR system will check the files of Update folder and if configuration file

26 1.6.2 Local UI Upgrading Upgrade the DVR system firmware through Update button in System Setting window. [Note]  When upgrading DVR firmware,

27 CHAPTER 1 2. Plug the USB pen drive to USB port on DVR unit. Then, click Setup >> System and click Update button. 3. After click update b

28 4. Wait for a while, DVR system is starting to upgrade firmware. 5. After upgrade is completed, click OK and DVR system will reboot

29 CHAPTER 1 1.6.3 Remote ISP Upgrading User can upgrade the DVR firmware from remote PC. [Note]  The PC that uses to upgrade DVR firmware must

30 2. Run the ISP application on PC and enter the DVR’s IP address, Port (Remote Update Configuration port in Network setting), and Password (admin

31 CHAPTER 1 5. Then, click Confirm button to start upgrading procedure. If user wants to discontinue the upgrade procedure, click Sto

Manual Updates Following are listed the new functions for the version X9.03.24.00.07a and above of EH6000H series surveillance softwar

32 Chapter 2 Using the DVR Software 2.1 The Way to Operate DVR There are three ways can be managed the DVR unit: 1. Using mouse and keyboard Connec

33 CHAPTER 2 c. Select the hard disk from device list. d. Click Format button to start formatting e. When formatting is done, click OK. 5. Setup

34 2.2 Familiarizing the Buttons in Preview Mode Name Function (1) Exit - Reboot: To restart the DVR system. It is required to enter the passwo

35 CHAPTER 2 Name Function (8) Preview Switch to Preview mode. This allows you to view live camera display. (9) Playback Switch to Playback mode.

36 Name Function (18) De-interlace To enhance the video quality. Set the de-interlace mode to #1, if you are capturing motionless pi

37 CHAPTER 2 2.2.1 To Setup DVR System Logout Time User can set a system idle time for DVR system to logout the system automatically. The idle time

38 2.2.2 Setting Up and Using the Emap E-Map can hold up to 8 maps in *.jpg or *.bmp format. You may locate the camera, sensor and relay on the map.

39 CHAPTER 2 To Use the Emap 1. Click E-map. 2. In the Emap screen, click the camera icon to switch on the area where the camera is located on the

40 2.2.3.1 Setup the Analog PTZ Camera 1. Select the channel of analog PTZ camera on Preview UI. 2. Click PTZ button from preview UI. 3. In the

41 CHAPTER 2 2.2.3.2 Setup the IP PTZ Camera When IP PTZ camera has successful connected with the DVR system, user can use the PTZ function directl

Function Description Two way audio port is configurable (Network Setting) Allows user to modify the port number for two-way audio. Provides local inf

42 2.2.4 Using Event Log Viewer Show the record of activities that take place in the system. Click Close button to exit Event Log Viewer window. 1.

43 CHAPTER 2 2.2.4.1 Using POSViewer To clear all setting, click Reset button. Click Close button will exit POS Viewer window. Name Function (1)

44 2.3 Familiarizing the Buttons in Playback Mode To switch in Playback mode, click Playback button at the lower right corner of Preview mode user i

45 CHAPTER 2 Name Function (3) Hour Buttons Select and click to playback the recorded video file on the specific time frame. i The Hour buttons r

46 Name Function (13) Event log Show the record of activities that take place in the system. To filter the records, select and click the option but

47 CHAPTER 2 2.3.1 To Cut and Save the Portion of the Recorded Video 1. Use the Playback Control buttons or drag the bar on the playback progress b

48 2.3.3 To Search Using Visual Search 1. Click Visual Search. 2. In the Visual Search Setting dialog box, select the Camera number and the date

49 CHAPTER 2 4. On the time second screen, click the channel and playback button will appear. Click playback button to playback the selected channe

50 2.3.4 To Search Using the Event Search 1. Click on the video screen on where you want to search. 2. Click Event Search. The Event Search Sett

51 CHAPTER 3 Chapter 3 Customizing the DVR System In the Preview screen mode, click button to customize your DVR. When the DVR configuration setu

Table of Contents Manual Updates ...

52 (2) Hard Disk Calculator i Stop recording before using hard disk calculator function. Estimate the hard disk recording capacity. The result of c

53 CHAPTER 3 (7) Video Standard Change and select the proper video system according to your camera video system. If the video system setting is wro

54 2. In the POS Mapping dialog box, click OK to accept the settings and Cancel to exit without saving the new setting. (1)(2)(3)(4)(5)(6)(7) (1) N

55 CHAPTER 3 screen automatically when system boot up. User can manually to enable by clicking the CPU Meter button. (12) IP Camera Resolution Mode

56 (14) Date and Time Setting Click Setting button of System Date and Time to setup current date and time. Mark Daylight Saving Time to enable daylig

57 CHAPTER 3 3.2 Camera Setup The DVR system supports 8/16 cameras in combination of analog and IP cameras, only analog cameras, or only IP cameras.

58 - Description Add a short comment (5) IP Camera Information To setup IP camera and display current IP camera information. Using IP Camera Motio

59 CHAPTER 3 Detail: The setting of advanced IP cameras are related to the Intelligent Streaming function in System setting. Click Detail. Click De

60  I/O Control: Setup the sensor and relay that is embedded on the IP camera.  Sensor Setting 1. Click Sensor button. 2. Click the drop-down

61 CHAPTER 3 3.2.2 To Setup IP Camera(Flexible Mode) When user select IP camera resolution mode as Flexible mode in System Setting, the Camera Setti

2.2.1 To Setup DVR System Logout Time ... 37 2.2.2 Setting Up and Using th

62 - Name Click Edit to change the camera name. i DVR supports Chinese characters on remote site (remote setup). - Description Add a short comment

63 CHAPTER 3 Detail: The setting of advanced IP cameras are related to the Intelligent Streaming function in System setting. Click Detail. Click De

64  I/O Control: Setup the sensor and relay that is embedded on the IP camera.  Sensor Setting 1. Click Sensor button. 2. Click the drop-down

65 CHAPTER 3 (6) IP Camera Resolution Status i The total resolution values are including both IP camera channel and Remote DVR channel. It displays t

66 When one of connected IP camera’s resolution has been changed and is caused resolution over 8MP, the channel screen is displayed text word “Over R

67 CHAPTER 3 3.2.2.1 Using Search Device to Connect IP Camera The Search Device function help user to find the IP cameras on your LAN network that c

68 a warming message dialog is popup and click OK to continue it. In IP setting window, user can configure IP camera’s IP, Mask, Gateway, an

69 CHAPTER 3 3.2.3 To Setup Analog Camera Click Default will back to the factory default value. i EH6108H+ only supports 8 channels. (1) Camera Ico

70 (6) Enable Deinterlace Enhance the video quality. Set the Enable Deinterlace mode to #1, if you are capturing motionless picture and select #2, if

71 CHAPTER 3 - Description Add a short comment (5) IP Camera Information - IP Enter the IP address of the camera - Port The port for connection -

Chapter 4 Using the Remote Programs ... 101 4.1 Familiarizing the Buttons in

72 (2) Enable Set to enable/disable the selected camera. When there is no video source on the camera, we suggest disabling it so that the system won’

73 CHAPTER 3 If user ignores or doesn’t notice the resolution is over 8MP and click OK button to save the setting, then, a warning message dialog is

74 3.3 Recording Setup 3.3.1 Setup IP Camera Record Setting Click Default will back to the factory default value. i EH6108H+ only supports 8 chann

75 CHAPTER 3 if there is no motion, it records at key frame. - No Recording The system won’t do any recording. (3) Motion Detection Adjust the sen

76 Record Prior and Stop Record After settings. - Smart Recording Automatically switch to record at the maximum frame rate setting once a motion i

77 CHAPTER 3 (8) Mask i Mask and POS function cannot be enabled at the same time. Mark an area on the screen to disregards the motion in the marked

78 3.4 Network Setup Click Default will back to the factory default value. (1) Server Name Assign a name for the DVR unit. Alphabet letters and num

79 CHAPTER 3 - Mask: It is a bitmask used to identify the sub network and how many bits provide room for host addresses. Enter the su

80 - Enable White List i Without any IP address/IP range is assigned in White List table, none of IP address/IP range is allowed to access DVR when

81 CHAPTER 3 - Web Service Viewer It displays the current remote connection (such as PCViewer, Remote Console, CM3000) information. Same IP address

1 CHAPTER 1 Chapter 1 Introduction 1.1 Package Content 1.1.1 EH6108H+ (1) (2) (3) (4) (5) (6) (7) (8) (9) (1) DVR unit - EH6108+ wi

82 3.5 Schedule Setting Schedule to record, enable network, reboot and disable alarm of all the cameras either weekly or one time. The number from 0

83 CHAPTER 3 5. To end Schedule Setting, click OK to exit and accept the setting and Cancel to exit without saving the setting. 3.6 Backup Setup i

84 7. DVR system will give Folder Name automatically. 8. Click Backup Now button to start archiving the selected file.  Backup by Time User can se

85 CHAPTER 3 3.6.1 Using QPlayer to Playback Backup Video You can playback the backup files by using QPlayer applications on the PC. When you back u

86 Name Function (5) Playback Control Buttons Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame. Slo

87 CHAPTER 3 Name Function (12) Full screen View in full screen mode. To return, press the right button of the mouse or ESC on the keyboard or clic

88 3.6.3 To Search Using the Visual Search 1. Click Visual Search. 2. In the Visual Search Setting dialog box, select the Camera number and the

89 CHAPTER 3 3.6.5 To Search Using the Intelligent Search 1. Click on the video screen on where you want to search. 2. Click Intelligent Search. T

90 3.7 Sensor Setting The I/O device must be installed to use this function. 1. Click the drop-down list and select the sensor ID number. 2. Ent

91 CHAPTER 3 3.8 Relay Setting The I/O device must be installed to use this function. 1. Click the drop-down list and select the relay ID number. 2